Amazon

AD

Wednesday, July 5, 2017

Garbage to Gorgeous® #17: Glam Resin Table Makeover ~ DIY

Garbage to Gorgeous® is back!!!  I've had this table in my garage FOR-E-VER!  

I found the table on the side of the road, in the trash.  The top had broken slate and it was a little rusty.  I decided to go for a glam resin look, while adding natural elements.  The last time I did something like this, it was the Beauty of Nature Coaster and I wanted to try it on a larger scale.  




You will need:
-  Old table:  I found mine in the garbage at the side of the road
-  Tools to clean it up:  I used a hammer, chisel and wire brush
Wire brush:  http://amzn.to/2shdiv5
Resin:  http://amzn.to/2tg9VFZ
Pigment powders:  http://amzn.to/2tC0HGi
Rust converter:  http://amzn.to/2tGHcNp
Spray paint:  http://amzn.to/2tAhlX5
Dremel tool:  http://amzn.to/2shpFXW
Sander:  http://amzn.to/2uzYhoX

Items from nature:  sticks, dried leaves, sea shells, pine cones, shell of nuts, etc.  


Here is the video tutorial:




Directions:

1.  I broke out the slate on the table.



2.  Using a wire brush, clean off the rust and give the table a general cleaning.



 3.  I first painted it with a rust inhibitor/remover and then followed up with a black spray paint.




4.  I added a layer of glue to seal any seams, to make sure the table didn't leak, when I added the resin.  




 5.  I collected dried leaves, sticks, snail shells, walnuts, etc.




6.  I mixed resin and pigment powders.  I added leaves into the resin cups.  I added layers and layers of resin, added sticks, shells, leaves, etc.




7.  I kept adding layers.  The amount of resin needed, will depend on the size of your table.  Be sure to extra carefully pop bubbles, between layers.  Don't set your table on fire!



8.  When the last layer cured, I took a rotary tool and cut it down. 




9.  Then, I sanded it...nice and smooth.



10.  I added a final layer of clear resin, which brought out the beauty!




11.  Here's a close up of the table, but be sure to check out the video above and see all the beautiful sections on the table!





Be sure to check out these other 

Garbage to Gorgeous® projects: 



Here is the coaster I made with the 
same technique as the table:

Tuesday, July 4, 2017

Disney Princess~ The Little Mermaid Coaster ~ Another Coaster Friday ~ Craft Klatch DIY

If you love Disney Princesses and The Little Mermaid east, check out how to make this Ariel coaster DIY!




You will need:
Resin:  http://amzn.to/2sATFC0
Coaster mold:  http://amzn.to/2tvthpA
Seashells:  http://amzn.to/2s7QOMN
Aquarium rocks:  http://amzn.to/2s7Fdxh
Disney Princesses stickers: check your craft store
Glitters and bugle beads are best found at craft stores.


Here is the video tutorial:







Directions:
1.  Mix two ounces of resin.  Pour some into the coaster mold and add some aquarium rocks to the resin remaining in the cup.


2.  Drop three shells into the resin and make sure they are covered.  Remove shells from resin and add it to the mold.



3.  Scoop out the aquarium rocks and put them into the mold, creating a border.



4.  Add glitter, bugle beads, confetti, etc. to the remaining resin and pour it into the middle of the mold. 


5.  Pop the bubbles and allow it to cure at least 12 hours.



6.  Add the Ariel sticker to the resin.


7.  Mix one ounce of resin and pour it over the sticker.



8.  Pop the bubbles and allow it to cure.


That's it!  Thanks for stopping by!  Now you have a fun Little Mermaid coaster!

Be sure to check out these Disney Princesses too:




Remember:  Life's to short not to shimmer, so grab your glue gun and your glitter!™  Stay safe!

Mona